Discovering Plumbing Basics is Important When Installing a Bathtub
Discovering Plumbing Basics is Important When Installing a Bathtub
Blog Article
Were you on the lookout for critical information concerning How to Install a Bathtub?
Mounting a bathtub isn't exactly rocket science, however it does call for strong plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old bathtub with a new one is also a moderately challenging job. If the old tub is easily easily accessible, the project can move rapidly; if you have to open a wall to remove the old bathtub and also place the brand-new tub, the job is much harder. In either situation, the project is within a home handyman's abilities, although you will certainly need a helper to vacate the old bathtub as well as set in the new one. Make sure you have actually qualified yourself for the work as well as are comfortable trying it. Instead of hiring a contractor to take over a halfway-completed task, it is far better to take into consideration employing one prior to you begin. Opportunities are you may need an expert plumber to make tube connections.
This post will certainly aid you set up a brand-new bath tub in your bathroom if you have actually currently bought a brand-new tub as well as don't require to transform the arrangement of your previous water pipelines.
Your devices as well as product list ought to comprise the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is disconnect the water system. After doing so, activate the taps to drain pipes any water continuing to be in the system. The process of eliminating the existing taps can be fairly troublesome due to the limited gain access to that is often the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the faucets. Have a towel all set for the staying water that will originate from the pipes. Once the supply pipes have been removed, make use of the same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning throughout this process. Once the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any old sealing compound.
Before proceeding to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end offers a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly require minimizing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin guaranteeing that the washing machines remain in place between the tap as well as the sink. Safeguard the tap in position with the supplier given backnut. Once the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with regular faucet ports. The previous type ought to be connected to the faucet ends first, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Mounting the Tub
Utilizing the two wooden boards under its feet, place the tub in the called for placement. The wood boards are useful in evenly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto four little factors.
The next goal is to guarantee that the bathtub is leveled all round. This can be attained by examining the spirit level and readjusting the feet on the tub till the level reads level.
To mount taps, fit the bottom of the outermost flexible faucet adapter to the proper supply pipe by making a compression sign up with; after that do the very same for the various other tap.
Turn on the supply of water as well as check all joints and brand-new pipework for leakages as well as tighten them if needed. Fill up the bathtub as well as likewise check the overflow outlet and also the typical outlet for leakages.
Lastly, fix the bath paneling as defined in the producer's user's manual. Tiling as well as sealing around the tub should wait till the bathtub has actually been used at the very least once as this will certainly resolve it right into its final placement.
Getting ready for the Installment
First of all, the sustaining framework provided with the bath needs to be fitted (if needed) according to the supplier's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to ensure that if the tap features a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets device to stop pressure on the tub.
Fit the versatile tap ports to the bottom of the two taps making use of 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. See to it you utilize all of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its last position.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to break a rigid seal, causing the water to pass through the wall surface between the bathroom as well as the tiling, causing difficulties with wetness and possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures and fittings. They are sold in tubes and cartridges, and can sealing voids approximately a size of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly fill the bathtub with water prior to sealing, to permit the activity experienced when the tub remains in usage. The sealant can crack rather very early if you do not think about this motion before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also easily readily available on the market. It is suggested to fit the tiles making use of water-resistant or water-proof sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you liked our part on How to Install a Bathtub. Thanks a lot for taking time to read through our piece of content. Do you know about somebody else who is fascinated by the topic? Why not share it. Kudos for your time. Visit again soon.
Plumbing SOS? Dial! Report this page